ISO 16889 PDF

ISO HYDRAULIC FLUID POWER – FILTERS – MULTI-PASS METHOD FOR EVALUATINGFILTRATION PERFORMANCE OF A FILTER ELEMENT. Introduction. The obsolescence of AC Fine test dust (ACFTD) has led to the adoption of a new test dust, ISO Medium Test. Dust (ISO MTD), and the impending. ISO Multi-Pass Test. The multi-pass test is a means of determining a filter’s performance; it measures the ability of the filter to remove particles of test dust.

Author: Vigore Gardami
Country: Greece
Language: English (Spanish)
Genre: Literature
Published (Last): 10 November 2015
Pages: 177
PDF File Size: 9.90 Mb
ePub File Size: 10.28 Mb
ISBN: 128-5-45095-907-1
Downloads: 44435
Price: Free* [*Free Regsitration Required]
Uploader: Shajind

These standards have been developed to increase the precision in the measurement of contamination and filtration performance, and to extend the amount of information from the tests.

Clarifying the New ISO Contamination Filtration Standards

If the filter fails to provide the necessary control of damaging-sized particles, then their presence in the system will lead to a substantial increase in the number of particles generated within the system through a chain reaction of wear. The data that can be made available is as is.

Therefore, the desired level of control will not be achieved. The Role of the Filter To appreciate the importance of the filter in the management of the system, consider the primary function of iiso filter: The data that can be made available is as follows: Create your own user feedback survey.

This article will focus on the impact the new standards have on selecting candidate filters based on performance criteria. Current Issue Archive Advertise.

A filter must control the levels of all contaminant particles at and above the size critical to its operating system. However, the multi-pass test is carried out in a laboratory under steady-state conditions and does not represent strenuous operational conditions. The current data requirement is a substantial improvement.

Clarifying the New ISO Contamination Filtration Standards

The more critical the system, the stronger the filter element and the more frequent the monitoring required. Particles entering component working clearances will become work hardened and produce more wear particles.

  BURTON SONATINA FLUTE PDF

About the Author Mike Day. It is a preselection requirement that provides the user and specifier of filter standards with more consistent information. The Beta ratio is defined as: This demands care in the selection of the most appropriate filter for the system. More detailed information from the test has to be published than previously required. When the contaminated hydraulic fluid passes through the filtration medium, it takes the line of least resistance.

Consequently, the number of different Beta ratings used has proliferated.

The group also stipulated that detailing comprehensive performance data was necessary so users can make informed selections. Users of filters have historically 1889 the simplicity of a single point rating the size where a specified Beta ratio is attained.

It is able to control the critically sized particles better than Element B. The effectiveness of the hydraulic filter to control clearance-sized particles is essential if the desired level of reliability is to be realized in the hydraulic system concerned. What value is most appropriate? While primarily developed for fluid power, the new standards are equally applicable to the lubricating oil sector. It should allow fluid to pass through at the given flow with the minimum pressure drop DP to minimize stress and energy losses.

The Best Gets Better: To appreciate the importance of the filter in the management of the system, consider the primary function of the filter: The slope of the curve effectively defines the pore size distribution PSD of the filtration medium; the wider the PSD the less able the filter is to control those critically sized damaging particles. Strategies to Protect Grease Fittings from Contaminants. Users were often confused when comparing performance data of seemingly identical filters.

  946GZT-AM MANUAL PDF

In the s and s, a compromise was reached between what is desirable and what can be consistently achieved for the range of filters assessed by this test. The filter should control the fluid cleanliness to a level that is equal to the performance, life and reliability of the system required by the user.

Hydraulik├Âl-Filtrationssysteme | Donaldson Hydraulik

Toggle navigation Toggle search. Figure 2 shows the advantages of this approach. However because of particle count statistics in the multi-pass test, the absolute rating cannot be measured with any degree of confidence. This will be through the larger pores in the medium and any holes created by poor manufacturing techniques. It has to protect the components from the damaging, critical clearance-sized particles particles that can penetrate and interfere with the working clearances of components.

The need to remove particles consistently across a wide size range was recognized by the ISO Working Group responsible for updating the multi-pass filter test.

It is only when the ratings at higher Beta ratings 166889 considered that the differences in performance are clearly seen.

Additionally, the user can have greater assurance and confidence in the data, and designers or specialists can make a more informed judgment in the selection of the most appropriate filter for his system. Now, users can quickly see how the filter performs 16898 a specified range of particle sizes and jso compare the performance of candidate elements.

Therefore, the highest Beta ratio that can be reliably measured should be selected. The Beta ratio is defined as:.

This makes the capture of these particles, by the filter, essential to sustain the good health of the system.

VPN