LMN Texas Instruments Phase Locked Loops – PLL datasheet, inventory, & pricing. LMN Datasheet PDF, pdf, pinout, equivalent, replacement, schematic, manual, data, circuit, parts, datasheet. National Semiconductor LMN: available from 2 distributors. Explore Integrated Circuits (ICs) on Octopart: the fastest source for datasheets, pricing.

Author: Kajirr Yozshuk
Country: Sierra Leone
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 3 June 2008
Pages: 385
PDF File Size: 1.45 Mb
ePub File Size: 12.15 Mb
ISBN: 249-1-55806-906-8
Downloads: 62745
Price: Free* [*Free Regsitration Required]
Uploader: Sajas

The basic circuit diagram is shown in Figure 5 with a typical application. Pull-down resistors are incor- porated into each output and no external components are required for most fluorescent display applications. SUMMARY The phenomenal growth in display technology has largely come as a result of the electronic calculator, and electronic displays will pervade all datssheet lives in an ever-increasing number of products.

Parts with this higher voltage rating would create a potential for switching loads far in excess of watts! The nominal voltage for this type of panel is V. Improved customer satisfaction with performance and reliability is an immeasurable but cer- tain bonus of the program. This condition creates a potential for lm1391 of device outputs, or other potential control functions such as chopping or bi-level drive. This device can also be used to drive incandescent or heater loads.

Temperature Cycling This is a screening process designed to mechanically stress lm1391j integrated circuit by alternately heating and cooling it.

A d-c path of less than a must be provided between pins 4 and 6. New functions are becoming available along with increased power handling capability, high voltages, etc. The I-F transformer used with the ULN A has been made to utilize both outputs of the mixer and was datashete on a bobbin type coil form Toko Type 10EZ to maintain close couplings between windings.

Quality is the extent to which a device conforms to specifications when it is lj1391n ped to the datssheet. They are both able to handle the application shown in Figure 8 a basic d-c, non-multiplexed clock interface rather than a more complex multiplexed system.


Sprague, Dionics, RCA, Texas Instruments, National Semiconductor, and others are using these device technologies to carve market niches where suitable. This allows the tuner designer to select an R-F amplifier and oscillator cir- cuit best-suited to the particular application. Ion All inputs at 0. Minimum Data Pulse Width ns ns C. Switching can be accomplished through an ordinary switch or an appropriate power transistor.

A con- centration upon circuit design factors, improvements in DIP packaging copper alloy lead framesand tighter, tougher control of diffusion-related parameters has allowed the manufacture of quad power drivers rather than the dual mini-DIPs offered by TI.

This eliminates the high cost of a bifilar-wound transformer. Minimum data active time before strobe enabled data set-up time ns B.

Hermetically-sealed ver- sions of these devices with reduced package power dissipation capability are available. The step logic is activated on the positive-going edge, which in turn activates one of four output sink drivers. Outputs may be paral- leled for higher load current capability.

LMN Datasheet(PDF) – National Semiconductor (TI)

The input may be raised a maximum of 20 volts above ground and will function with input levels obtained from CMOS and open collector TTL 4. The high-current capabilities and high gain of the Sprague drivers represent poten- tial solutions to many difficult LED display systems – alphanumeric, seven-segment, or matrix; common- cathode or common-anode; continuous or multiplexed.

All outputs are pinned opposite their respective inputs to simplify circuit board layout. A single resistor at the same pin will adjust the A-M gain for op- timal system performance. The bipolar outputs are suitable for use with relays, solenoids, stepping motors, LED or incandescent displays, and other high-power loads.

Typical applications include driving peripheral loads such as incandescent lamps, light-emitting diodes, memories, and heaters with a load current of up to a mA peak value. Series UDNA high-voltage, high-current source drivers are supplied in lead dual in-line packages.

【LM1393】Electronic Components In Stock Suppliers in 2018【Price】【Datasheet PDF】USA

datawheet A fully-balanced, four stage differential I-F amplifier gives maximum gain with freedom from interference and noise. No doubt other applications will arise in the future, but these figures are representative of power interface applications which may be simplified through the use of these Sprague power integrated circuits to replace discrete components. Nothing currently on the market exceeds 1.


A simple, and less expensive solution is the use of mono- lm191n integrated circuits. Although not widely known, these quad driver units were developed quite independently and simultaneously to the ubiquitous TI series of high-speed, low- voltage peripheral drivers.

Be- cause of limitations on package power dissipation, simultaneous operation of all drivers at maximum rated current can only be accomplished with a reduc- tion of duty cycle.

Each driver tested separately. Minimum data active time after strobe disabled data hold time ns C. Although typically less than 1 per cent of a lot will be rejected, user confidence in lot integrity is greatly improved.

All devices in this series incorporate input current limiting resistors and out- put transient suppression diodes. In turn, the individual driver dissipation is the product of the collector- emitter saturation datasheey, the collector current, and the duty cycle.

Input Impedance Z 6. The transistor switch with current-limiting resistor scheme used in Sprague gas discharge display drivers also minimizes problems associated with gas panel arcing which can destroy programmable current cir- cuits.

Both use the glow transfer principle of the dot matrix Self-Scan display. Switching between modes can be accomplished with a simple single-pole d-c switch. Products have been and are being developed, using microprocessors and displays, that never previously existed. Each output stage of both integrated circuits will withstand output OFF voltages of – 80 V and load currents as high as mA. LOW total package 1.